Hydro Jetting in Montgomery

What is under a Montgomery lot

The oldest pipe in Montgomery is in the village center, where the houses along Montgomery Road, Cooper Road and the historic district streets date from the 1800s and early 1900s and sit on vitrified clay laterals. The neighborhoods that made the city, off Pfeiffer Road, Zig Zag Road, Weller Road and the streets toward Twin Lakes, were built from the 1950s into the 1990s on lots that are often half an acre or more.

The 1950s and 1960s homes have clay or, in some streets, Orangeburg fiber pipe. From the mid-1970s on, PVC is standard, and in the 1980s and 1990s subdivisions the lateral is plastic end to end. The distinguishing feature here is length. With the house set far back from the road, a lateral of 100 to 150 feet is ordinary, and many run through a wooded front yard before reaching the main under the street. Cast iron handles the stretch through the foundation and under any slab.

Why long laterals under big trees fail

Montgomery sits on glacial till, a dense clay over limestone and shale, draining to Sycamore Creek. The clay swells and shrinks with the seasons and frost reaches about 30 inches, so the ground works at every joint year after year. On a 120-foot clay lateral that is 40 or 50 joints, each one a potential crack or offset.

The trees are the main story. Pin oaks, white oaks, silver maples and sycamores that were saved or planted when the lots were developed now have root systems that extend far past their canopies, and the moist, nutrient-rich air inside a leaking sewer joint draws them in. Even PVC laterals are not immune if a glued joint was made poorly or the pipe settled and pulled apart. Transitions are the other weak spot: where a newer plastic addition was tied into an old clay run, the joint between materials is often where the camera finds the break.

Why lining suits Montgomery

Cured-in-place lining is almost built for long laterals. After hydro jetting and root cutting, the installer inverts or pulls a continuous epoxy-saturated felt liner from the cleanout to the main and cures it with hot water, steam or UV. One liner can cover 150 feet in a single shot, sealing every joint and transition, and it is installed from the house end with no pits in the front yard. The host pipe must be round; the camera settles that question first.

Pipe bursting is the fallback for a collapsed section, a severe offset or oval Orangeburg. The crew digs a pit at the house and another at the main, pulls a bursting head through, and tows fused HDPE behind it. On a long Montgomery lateral, the pull itself is routine but the receiving pit may need to be in the tree lawn near the street. For a single broken joint or a failed transition on an otherwise sound line, a sectional point repair over that few feet is the economical fix.

MSD, the city and the inspection

Montgomery is in the Metropolitan Sewer District of Greater Cincinnati service area, and MSD issues the building sewer permit and inspects open pits or the post-installation video. The City of Montgomery permits any work in the public right-of-way, including a receiving pit in the tree lawn. The owner is responsible for the lateral to the main, so both permits are part of the owner's project, pulled by the contractor.

On a lined lateral, the inspection is usually a video review. On a burst one, the inspector sees the connection at the main before the pit is closed. Ask the contractor how the connection to the main will be sealed, because a liner that ends short of the main leaves a gap where roots return.

The job day and choosing the installer

The crew will camera the full length, locate and mark it across the yard, and record depths, especially at the street. After jetting and a second inspection the liner goes in and cures over a few hours, during which the house cannot drain. The final video shows a smooth continuous bore from cleanout to main.

For a long lateral, ask whether the crew has lined runs of this length in one shot or whether they plan to line in sections, and ask how the sections will be joined. Request the videos, the liner spec and the warranty in writing. To compare installers who serve Montgomery, find a verified CIPP contractor and get a camera report from each before deciding.

Hydro Jetting in Montgomery

What a jetter does that a cable cannot

A hydro jetter pushes water through a nozzle at several thousand PSI. Rear-facing jets pull the hose down the line and scour everything off the pipe wall: roots, grease, sludge, mineral scale, and the rust flakes inside old cast iron. A cable machine drills a hole through the blockage and leaves the rest on the wall, which is why cabled lines re-clog on a schedule.

Where it fits in a repair

Jetting is step one before lining, because a liner has to bond to clean pipe, and step one before an honest camera inspection, because a line full of roots or scale hides its own condition. It is also legitimate maintenance on its own for a structurally sound line that roots keep finding.

When a line should not be jetted

Cast iron that is paper-thin at the bottom can be opened up by an aggressive descaling pass. A collapsed clay section will not let the hose through. Orangeburg can delaminate under pressure. An experienced operator checks the line first, matches the nozzle to the material, and stops if the pipe is not holding up.

Maintenance versus repair

If the camera shows sound pipe, annual or semiannual jetting is a cheap way to stay ahead of roots. If it shows open joints, channeled cast iron or offsets, jetting is a stopgap and the money is better spent on lining, which removes the joints the roots are using.

More trenchless services in Montgomery

Questions we hear in Montgomery